99久久国产免费福利_瑜伽裤国产一区二区三区_丝袜人妻无码专区视频_国产美女视频国产视视频

本文由金屬剪切機、廢鋼打包機廠家江陰市鳴澄液壓機械有限公司整理提供，更多資訊請?jiān)L問：tongchuangbio.com

    半自動打包機常見故障現象：半自動打包機正常開機，打完包后開始自動送帶，而且是無限送帶。
    解決方法：檢查機器除了自動送帶以外是否工作正常。如其他部件無故障現象，則很可能是電位器出了問題。電位器，在打包機正面，操作面板上總共有四個按鈕，從左至右依次是電源開關、電位器、復位按鈕、送帶按鈕。打包機電位器為旋轉按鈕，周圍標有刻度，是用來控制打包完成后自動送帶的長度的。如果出現送帶不止，且自動送事帶沒問題，多半是電位器失靈所致。
    調試方法，將電位器旋至最小刻度，然后微調，在一個范圍內機器是可以正常送帶的。如果在某個區間內送帶正常，則可以肯定是電位器故障。接下來就是更換電位器。
    建議使用精確控制電位器。操作方法：
    1.用小螺絲刀將固定在黑色旋鈕上的小螺釘卸掉，取下黑色旋鈕。
    2.擰掉固定螺絲，從里側將電位器拔下。可看到電位器有三個出線位，其中兩個與電腦板連線，另一個斷路。
    3.記住線序用烙鐵將電位器取下。然后更換新的電位器。
    4.再一次將電位器重新裝好。Fault phenomenon: semi-automatic strapping machine normal boot, began after automatically send finished packing belt, and is infinite send belt.
Solution: check the machine in addition to automatically send belt is working correctly. If other parts trouble-free phenomenon, is likely to be problems with the potentiometer. Potentiometer, in baling press positive, there were a total of four buttons on the operation panel, from left to right in turn, is the power switch, potentiometer, reset button, send button. Baling press potentiometer to rotate button, around with scale, is used to control after the completion of the automatic to send with the length of the packaging. If appear to send belt, and automatically send it with no problem, mostly caused by potentiometer failure.
Debug method, the potentiometer to the smallest scale, and then fine-tuning, within the scope of a machine can be normal to send belt. If in a certain interval send with normal, is certainly potentiometer failure. The potentiometer is replaced.
It is recommended to use precise control potentiometer. Operation method:
1. With a small screwdriver on the black knob screw off, remove the black knob.
2. Turn off the fixed screw, from the side will remove the potentiometer. Can see there are three round a potentiometer, including two plate connection with computer, and the other a break.
3. Remember that line sequence with iron potentiometer. Then replace the new potentiometer.
4. Will potentiometer to pack again.